How To Set The Timing On A Juki Sewing Machine

Download Article

Download Commodity

Your sewing machine's timing is essential to achieving fifty-fifty stitches in your material and ensuring that the machine'due south parts are working in sync. Although the full general process for adjusting timing is the same for most sewing machines, the method of removing, modifying and installing parts is different for each automobile, so consult the owner'due south manual of your machine every bit you get through the stages of checking and fine tuning the timing on your automobile.

1. 

   1

   Bank check for other potential problems. Check other factors that may masquerade as a timing problem first; there'southward no sense in taking your machine apart if y'all don't demand to!

   • Exist certain that your needle is non aptitude or broken and that it is inserted completely and screwed downward tightly.
   • Cheque that your bobbins are installed correctly. If they're upside-down or astern, your machine might non work correctly.
   • Check that your needle, thread weight, and cloth are compatible. A heavier cloth requires a larger needle and thicker thread.

2. 

   2

   Check for a timing consequence past performing a timing test. By testing the alignment of the needle and the shuttle claw, you can determine whether your car needs a timing adjustment.

   • Leave the needle threaded, but remove the switchplate, base embrace(south), and bobbin instance.
   • Plow the hand bicycle slowly to ensure that the shuttle claw is smoothly communicable the thread. If it does not, yous may need to suit the timing.
   • Use a ruler to measure the timing settings. Use the mitt bike to put the needle in the lowest position, then enhance it iii/32 of an inch. The shuttle hook should meet the needle just above the eye while it is in this position. If it does not, y'all may need to adjust the timing.

   Ad

3. 

   3

   Prepare the machine for work. If yous have determined that you need to adjust the timing, be sure you are ready to work on your machine.

   • Yous may demand motility the sew position to a directly stitch, ensuring that the needle descends through the center of the switchplate hole, or you lot may demand to move your needle to the widest zigzag position. Check with your manufacturer's guidelines.
   • If you oasis't already, remove the needlebar comprehend, the switchplate, the bobbin, and the encompass from the base of operations of the auto. ^[one]
   • Assemble any tools you may demand, such every bit a small screwdriver, sewing machine oil, and a bright work lite.

Advertizing

1. 

   1

   Set the needlebar height. Well-nigh machines have marks on them that indicate the appropriate meridian for the needlebar. Consult your manual for specifics on how to access and loosen your needle bar.

   • If timing marks are nowadays, loosen the needlebar and slide it up or down to align the acme timing marker just below the lesser of the timing bar bushing.
   • If timing marks are non present, lower the needle completely with the hand bike, then raise it 3/32 of an inch (ii.4mm). Adjust the needle'southward height so that the needle heart is 3/32 of an inch below the betoken of the hook. ^[ii]

2. 

   ii

   Fix the claw timing. Adjusting the claw timing varies between manufacturers and models. The general approach, even so, is to accommodate the distance between the hook and the needle.

   • Using the handwheel, lower the needlebar to its lowest position.
   • Loosen the gears in the base of the machine.
   • Make adjustments until the claw and needle are an appropriate distance autonomously, anywhere from 0.04mm to 0.1mm ^[3] or 0.01-0.xvi, depending upon the machine.

3. 

   three

   Re-Check for timing accuracy. By re-testing the alignment of the needle and the shuttle hook, yous tin can determine whether your adjustments accept improved the machine's settings.

   • If y'all removed the thread from the needle, re-thread information technology. Continue to work with the bobbin expanse exposed.
   • Turn the manus bike slowly to ensure that the shuttle hook is smoothly communicable the thread. If the claw catches the thread every fourth dimension, your timing has been stock-still.

Advert

1. 

   1

   Re-get together your automobile. Carefully tighten all screws securely, and be sure there are no "leftover" parts that have not been replaced.

2. 

   2

   Clean and oil any exposed gears while your covers are yet off. ^[iv]

   • Remove whatever lint or debris from gears and feed dogs.
   • Consult your manual to find the specific areas that crave oiling.
   • Just use sewing auto-specific oil on your sewing machine.

3. 

   3

   Supervene upon the covers and switchplate.

4. 

   four

   Test your adjustments. Re-thread your machine and sew a test piece of cloth.

   • The stitches should be even, with no skipped stitches or broken needles.
   • If the problem has not been resolved, y'all may demand to make further adjustments or consult a sewing machine repair person.

Advertisement

Add New Question

• Question

  How do I conform the speed of the pes command pedal?

  

  The human foot control pedal for a motorcar is nigh always matched to the functioning of the motorcar. If the maximum speed is too slow for you, then you lot need to upgrade. Near machines accept limits. High operation machines are dynamically balanced and will sew in excess of a foot per 2nd. Domestic machines are non counterbalanced and don't run anywhere near equally fast as a professional person Pfaff, for example. If it seems very slow, and then something has gone wrong and you will need a specialist.

• Question

  Could thread jams be a sign of problems with the machines timing?

  

  A lot of thread jams can be fixed with a new needle. Brand certain your machine is oiled properly as well. Refer to your user's manual for instructions in this.

• Question

  What do I practice if the bobbin case thread does non take hold of the needle thread?

  

  It tin only be 2 things: either the thread isn't existence taken low enough to catch the hook, or the timing is out and the bobbin hook is missing the thread due to beingness in the wrong position. First, try lowering the needle a fraction.

Show more answers

Advertisement

Video

• Always unplug your machine earlier performing whatsoever maintenance or repair work.

• Be sure to check the warranty information and user manual for your specific sewing machine before making adjustments.

Advertizement

Things You lot'll Need

• Sewing machine
• Instruction manual for your sewing machine
• Screwdriver
• Sewing thread
• Strip of cotton fiber cloth
• Cleaning solvent

Virtually This Article

Article Summary 10

To adjusting your sewing machine's timing, commencement by loosening the needlebar and sliding it up or down to align the pinnacle timing mark just beneath the lesser of the timing bar bushing. If your needlebar doesn't have timing marks, lower the needle completely using the manus wheel, so raise it 2.4 millimeters. Adjust the needle height so the needle heart is 2.4 millimeters below the point of the hook. Once you've set the needlebar summit, adjust the hook timing by lowering the needlebar to the lowest position. Then, loosen the gears in the base of the machine. Finally, arrange the claw until it'south the correct distance from the needle. A normal distance is annihilation from 0.04 to 0.1mm. For more than tips, including how to test your sewing machine's timing, read on!

Did this summary aid yous?

Cheers to all authors for creating a page that has been read 460,159 times.

Did this commodity help y'all?

Source: https://www.wikihow.com/Adjust-Sewing-Machine-Timing

Share this post